Tuesday, September 15, 2015

Scrap Buster - Earbud Case or Tiny Coin Purse Tutorial


There are a gazillion zipper bag tutorials out there and I have made many of them. When I wanted one to fit my earbuds, I couldn't quite find exactly what I wanted. I wanted it to be the perfect size to fit my earbuds. I don't like to over clutter my purse, I wanted something flat, and I wanted a ring attached so I could have the option to clip it to my purse, key ring, etc. This case is very small but you could also use it for a small coin purse, or as a place to hold your flash drives and extra SD cards. The nice thing about this pattern is that you can easily make it any size you want. Just remember that your zipper must extend at least an inch or an inch and a half past the edges on each side. The finishes size of mine is 3 X 4 inches, and the top stitching around the outer edges takes up some of the inside space, which can be omitted if you prefer. Let's begin!

Supplies to make one zipper bag
Scrap fabric for outside, lining, and optional tab
Scraps of fusible interfacing (I used fusible fleece interfacing)
Thread to match fabric
9 inch or larger zipper
1 inch metal ring (optional)
General sewing supplies such as cutting tools, scissors needles, pin, sewing machine, iron.

Note: If your fabrics will be pre-washed, do not use fabric softener. It can prevent your fusible interfacing from sticking.

Instructions
1.  Make a paper template to measure 4 1/4" X 5". Remember that this is a tiny case so if you want yours bigger, this is the time to change the measurements. Just remember that your zipper must be bigger.

Fold the paper template into quarters and round off the corners. Using this template, cut two pieces from the outer fabric, two pieces from the lining fabric, and two pieces from the fusible interfacing. You are also going to cut a piece 2" X 2" fabric piece for the tab if you are going to add the ring.

2.  Take one of each of your fabric and interfacing pieces and fold in half lengthwise, then cut down the center. You will now have one whole piece and two half pieces of the outer fabric, the lining, and the interfacing.


3.  Iron the fusible interfacing to the backside of each of the outer bag pieces. Be sure to follow the manufacturer's instructions for the interfacing you are using. If any of the interfacing extends beyond the fabric, just trim it away.

4.  Fold the optional tab fabric (2" X 2" square) in half, then fold the the two long edges in to meet the fold in the center and iron. Stitch along each folded edge.


5.  Sandwich your zipper between one of the outer half fabric pieces and the lining fabric pieces, meeting the long edges. The right sides of the fabric will be facing each other, and the right (top) side of the zipper will be facing the outer bag fabric. Make sure that the two fabric pieces match up evenly, and that the zipper is extending beyond each end. Also, your zipper slider is in the extended area and not between your two fabric pieces.


6.  Using your zipper foot, stitch the zipper and fabric pieces together 1/4 inch away from the edges. Flip the fabrics out and away from the zipper, lining them up so they match up, and press. Pin to secure. Take back to the machine and top stitch close to the fold. Repeat these steps with the remaining halves of the fabric by attaching them opposite of these two. Be sure to make them line up with the fabrics that are already stitched.




7.  Pull your zipper slider down so that it is a little more than halfway. You will need this opening to turn your case right side out. Trim the ends of the excess zipper pieces away.


8.  You will use your multi-purpose foot to stitch the the rest of the case. First, stitch the ends together so that the open ends of the zipper will meet each other. Keep your stitching within 1/4 inch from edge. You don't want the zipper teeth to overlap each other, you want them to meet. and remain flat.

9.  If you are using the tab and ring, you will attach that now. Fold the tab in half over the ring and stitch the ends together to secure. Place this piece at the edge that you just stitched closed. Stitch to the edge just under 1/4 inch from the edge.


10.  With the right sides facing out, and the interfacing on the inside, pin your large outer fabric piece to your lining fabric piece. Baste around the entire thing just under 1/4 inch from the outer edge.

11.  With the outer pieces facing each other, place this piece together with the zippered piece. You will notice that the fabric making up the bottom of the case is slightly bigger than the the zippered piece. That's OK, you'll be cutting it away later. With the zippered piece on the top, stitch around the case 1/4 inch away from the edge of the zippered piece. Make sure that your tab and ring are laying flat so they won't interfere with your stitching.



12.  Trim around the entire case about 1/8 inch away from stitching. Turn case right side out through the opened zipper, and iron. Top stitch all the way around the case. If you want this case to be a wee bit bigger, or you prefer the puffy look instead of the flat look, you can omit the top stitching. Enjoy!


Do you like free embroidery designs and tutorials?

Be sure to sign up for the weekly newsletter to get a free design every weekend (unless I'm running a sale). Sign up for Sher's Creative News

4 comments:

  1. Great idea! I think I'm needing an ear bud case too.

    ReplyDelete
  2. These are so cute Sher! So many possible uses too. I bet they would be great for storing lipstick in your bag.

    ReplyDelete
  3. great tutorial! I like all the fun fabrics!

    ReplyDelete

I LOVE to read your comments!

Related Posts Plugin for WordPress, Blogger...